Does Car-Z work with your Chevrolet?
What works, from which year, where the port is and what to watch out for.
From which year
With an ordinary plug. Years are model years.
| Fuel | Europe (incl. UK) | United States |
|---|---|---|
| Petrol | From 2001 | From 1996 |
| Diesel | From 2004 | From 1997 |
| Hybrid or plug-in hybrid | From 2008 | From 2008 |
| Electric | Partly | Partly |
Check your Chevrolet
Choose make, year and fuel. The answer appears right away.
Choose a make and a year to see the answer.
General guidance based on the law and known information per make; not a guarantee for one specific car. You also need a suitable plug and browser: see the guides.
What Car-Z reads
- Live data: speed, revs, temperatures, engine load, boost and more, as far as the car reports them.
- Stored and pending fault codes of the engine and emission-related systems.
- Clearing those codes, always only after you confirm.
- The vehicle identification number (VIN), if the car reports it.
- The 12-volt battery voltage.
What it doesn't do
- Fault codes from modules such as ABS, airbags or body electronics: those are manufacturer-specific.
- Coding, programming, adaptations or service resets.
- Battery health of electric cars and hybrids.
- Keys, immobiliser or odometer.
Where is the OBD2 port?
Look for a 16-pin, trapezoid-shaped socket. Usually:
Under the dashboard on the driver's side, near the pedals or the steering column.
In right-hand-drive cars (UK, Ireland) the port is usually on the driver's side too, but some models keep it on the left.
Security gateway
GM Global B (VIP)
from 2020 · Applies to: United States, Europe (incl. UK)From about 2020, GM uses a new, secured electrical architecture. Standard OBD stays readable; programming and some manufacturer functions are protected.
Electric and hybrid
Electric cars don't have to support standard OBD. Usually little comes through: the 12-volt voltage works, fault codes and live values often don't.
Hybrids have a combustion engine and therefore full standard OBD. Engine data comes through while the engine runs; battery data is manufacturer-specific.
Protocols per period
Typical for this make; it can differ per model. A good ELM327 plug supports all OBD protocols and picks the right one itself.
- SAE J1850 VPW1996–2007 · standard OBD
- ISO 15765 CANsince 2003 · standard OBD
Good to know
- In Europe, Chevrolet mainly sold former Daewoo models until 2015; after that only the Corvette and Camaro, plus imports.
- American cars up to about 2007 often use SAE J1850 (PWM at Ford, VPW at GM and Chrysler). Many cheap ELM327 clones handle this poorly, so use a good-quality plug.
- In the US, heavy pickups over 8,500 lb (3,856 kg), such as 2500/3500 models, came under the OBD rules later than cars. Older heavy pickups may not have standard OBD.
- Battery health (SoH) and exact state of charge of electric models are manufacturer data, not standard OBD. The app doesn't show them.
Tested in practice
What we and other drivers found with a real Chevrolet. The rules above are a guideline; this is what actually happened.
No tests with a Chevrolet yet
We haven't tested a Chevrolet ourselves yet and fewer than 3 drivers have shared their results. Drive a Chevrolet? Connect once and share anonymously whether it worked.
| Model and years | Status | What works | Dongle and protocol |
|---|---|---|---|
| All modelsfrom 2001 · Petrol · Europe (incl. UK) | ExpectedBased on the rules, not tested yet |
| – |
| All modelsfrom 2004 · Diesel · Europe (incl. UK) | ExpectedBased on the rules, not tested yet |
| – |
| All modelsfrom 2008 · Hybrid or plug-in hybrid · Europe (incl. UK) | ExpectedBased on the rules, not tested yet |
| – |
Verified: tested by us or a garage. Reported: at least 3 drivers shared the same result. Expected: follows from the rules, not tested yet.
Frequently asked questions
From which year does Car-Z work with a Chevrolet?
With a standard OBD2 plug: petrol from 2001 in Europe, diesel from 2004 in Europe, petrol from 1996 in the US, diesel from 1997 in the US. Older cars usually lack standard OBD.
Where is the OBD2 port in a Chevrolet?
Under the dashboard on the driver's side, near the pedals or the steering column.
Can I clear fault codes on my Chevrolet?
Yes, standard engine fault codes can be cleared, always only after you confirm. Note: clearing also resets the readiness monitors, which matters for an emissions test.
Does Car-Z work with an electric Chevrolet?
Partly. Electric cars don't have to support standard OBD, so usually only the 12-volt voltage and a few values come through. Battery health is manufacturer data and isn't shown.
Which plug do I need?
An ordinary, open OBD2 plug with Bluetooth LE that understands the standard ELM327 commands. Not a closed plug that only works with its maker's own app. The guides list which plugs we've tested and how to connect them.
Can Car-Z code or program my Chevrolet?
No. Car-Z reads standard OBD: live data and engine fault codes. Coding, programming and service resets need manufacturer-specific tools.
Sources
- Directive 98/69/EC (EUR-Lex)
- US EPA – OBD on 1996 and newer vehicles
- Autel – Security gateways (North America)
- Klavkarr – OBD port location Chevrolet
How sure we are: Medium: based on reliable sources, with some details per model still uncertain.
Related makes
Ready to read your Chevrolet?
Put a small plug in the port, open the app and connect.