Skip to content
SearchFree account
Menu
China · OBD2 compatibility

Does Car-Z work with your Lynk & Co?

What works, from which year, where the port is and what to watch out for.

From which year

With an ordinary plug. Years are model years.

FuelEurope (incl. UK)
PetrolFrom 2017
Hybrid or plug-in hybridFrom 2018
ElectricPartly

Lynk & Co wasn't officially sold in the US; imported cars follow the rules of the market they were built for.

Check your Lynk & Co

Choose make, year and fuel. The answer appears right away.

Where was the car sold new?

Choose a make and a year to see the answer.

General guidance based on the law and known information per make; not a guarantee for one specific car. You also need a suitable plug and browser: see the guides.

What Car-Z reads

  • Live data: speed, revs, temperatures, engine load, boost and more, as far as the car reports them.
  • Stored and pending fault codes of the engine and emission-related systems.
  • Clearing those codes, always only after you confirm.
  • The vehicle identification number (VIN), if the car reports it.
  • The 12-volt battery voltage.

What it doesn't do

  • Fault codes from modules such as ABS, airbags or body electronics: those are manufacturer-specific.
  • Coding, programming, adaptations or service resets.
  • Battery health of electric cars and hybrids.
  • Keys, immobiliser or odometer.

Where is the OBD2 port?

Look for a 16-pin, trapezoid-shaped socket. Usually:

Under the dashboard on the driver's side, near the pedals or the steering column.

In right-hand-drive cars (UK, Ireland) the port is usually on the driver's side too, but some models keep it on the left.

Security gateway

We know of no for Lynk & Co that affects standard . Newer cars increasingly have one; reading standard stays available, because emission checks depend on it.

Electric and hybrid

Electric cars don't have to support standard . Usually little comes through: the 12-volt voltage works, and live values often don't.

Hybrids have a combustion engine and therefore full standard . Engine data comes through while the engine runs; battery data is manufacturer-specific.

Protocols per period

Typical for this make; it can differ per model. A good plug supports all protocols and picks the right one itself.

  • ISO 15765 CANsince 2017 · standard OBD
  • DoIP (Ethernet)since 2017 · manufacturer tools only

Good to know

  • Lynk & Co shares most of its electronics with Volvo, so what applies there largely applies here too.
  • Hybrids report engine data through standard OBD. Data on the hybrid battery (charge, cell voltages, health) is manufacturer-specific, and the app doesn't read it.

Tested in practice

What we and other drivers found with a real Lynk & Co. The rules above are a guideline; this is what actually happened.

No tests with a Lynk & Co yet

We haven't tested a Lynk & Co ourselves yet and fewer than 3 drivers have shared their results. Drive a Lynk & Co? Connect once and share anonymously whether it worked.

Model and yearsStatusWhat worksDongle and protocol
All modelsfrom 2017 · Petrol · Europe (incl. UK)ExpectedBased on the rules, not tested yet
  • Live data: works
  • Read codes: works
  • Readiness: works
–
All modelsfrom 2018 · Hybrid or plug-in hybrid · Europe (incl. UK)ExpectedBased on the rules, not tested yet
  • Live data: works
  • Read codes: works
  • Readiness: works
–

Verified: tested by us or a garage. Reported: at least 3 drivers shared the same result. Expected: follows from the rules, not tested yet.

Frequently asked questions

From which year does Car-Z work with a Lynk & Co?

With a standard OBD2 plug: petrol from 2017 in Europe. Older cars usually lack standard OBD.

Where is the OBD2 port in a Lynk & Co?

Under the dashboard on the driver's side, near the pedals or the steering column.

Can I clear fault codes on my Lynk & Co?

Yes, standard engine fault codes can be cleared, always only after you confirm. Note: clearing also resets the readiness monitors, which matters for an emissions test.

Does Car-Z work with an electric Lynk & Co?

Partly. Electric cars don't have to support standard OBD, so usually only the 12-volt voltage and a few values come through. Battery health is manufacturer data and isn't shown.

Which plug do I need?

An ordinary, open OBD2 plug with Bluetooth LE that understands the standard ELM327 commands. Not a closed plug that only works with its maker's own app. The guides list which plugs we've tested and how to connect them.

Can Car-Z code or program my Lynk & Co?

No. Car-Z reads standard OBD: live data and engine fault codes. Coding, programming and service resets need manufacturer-specific tools.

Sources

  1. Directive 98/69/EC (EUR-Lex)

How sure we are: Low: limited sources. Treat this as a first indication.

← All makes

Ready to read your Lynk & Co?

Put a in the port, open the app and connect.