Skip to content
SearchFree account
Menu
Germany · OBD2 compatibility

Does Car-Z work with your smart?

What works, from which year, where the port is and what to watch out for.

From which year

With an ordinary plug. Years are model years.

FuelEurope (incl. UK)United States
PetrolFrom 2001From 1998
DieselFrom 2004From 1999
ElectricPartlyPartly

Check your smart

Choose make, year and fuel. The answer appears right away.

Where was the car sold new?

Choose a make and a year to see the answer.

General guidance based on the law and known information per make; not a guarantee for one specific car. You also need a suitable plug and browser: see the guides.

What Car-Z reads

  • Live data: speed, revs, temperatures, engine load, boost and more, as far as the car reports them.
  • Stored and pending fault codes of the engine and emission-related systems.
  • Clearing those codes, always only after you confirm.
  • The vehicle identification number (VIN), if the car reports it.
  • The 12-volt battery voltage.

What it doesn't do

  • Fault codes from modules such as ABS, airbags or body electronics: those are manufacturer-specific.
  • Coding, programming, adaptations or service resets.
  • Battery health of electric cars and hybrids.
  • Keys, immobiliser or odometer.

Where is the OBD2 port?

Look for a 16-pin, trapezoid-shaped socket. Usually:

Under the dashboard on the driver's side, near the pedals or the steering column.

In right-hand-drive cars (UK, Ireland) the port is usually on the driver's side too, but some models keep it on the left.

Port location per model (Klavkarr) ↗

Security gateway

We know of no for smart that affects standard . Newer cars increasingly have one; reading standard stays available, because emission checks depend on it.

Electric and hybrid

Electric cars don't have to support standard . Usually little comes through: the 12-volt voltage works, and live values often don't.

Protocols per period

Typical for this make; it can differ per model. A good plug supports all protocols and picks the right one itself.

  • ISO 9141-2 (K-line)2001–2006 · standard OBD
  • ISO 14230 KWP2000 (K-line)2001–2008 · standard OBD
  • ISO 15765 CANsince 2004 · standard OBD

Good to know

  • smart shares most of its electronics with Mercedes-Benz, so what applies there largely applies here too.
  • Since 2020, smart only builds electric cars.
  • Battery health (SoH) and exact state of charge of electric models are manufacturer data, not standard OBD. The app doesn't show them.

Tested in practice

What we and other drivers found with a real smart. The rules above are a guideline; this is what actually happened.

No tests with a smart yet

We haven't tested a smart ourselves yet and fewer than 3 drivers have shared their results. Drive a smart? Connect once and share anonymously whether it worked.

Model and yearsStatusWhat worksDongle and protocol
All modelsfrom 2001 · Petrol · Europe (incl. UK)ExpectedBased on the rules, not tested yet
  • Live data: works
  • Read codes: works
  • Readiness: works
–
All modelsfrom 2004 · Diesel · Europe (incl. UK)ExpectedBased on the rules, not tested yet
  • Live data: works
  • Read codes: works
  • Readiness: works
–

Verified: tested by us or a garage. Reported: at least 3 drivers shared the same result. Expected: follows from the rules, not tested yet.

Frequently asked questions

From which year does Car-Z work with a smart?

With a standard OBD2 plug: petrol from 2001 in Europe, diesel from 2004 in Europe, petrol from 1998 in the US, diesel from 1999 in the US. Older cars usually lack standard OBD.

Where is the OBD2 port in a smart?

Under the dashboard on the driver's side, near the pedals or the steering column.

Can I clear fault codes on my smart?

Yes, standard engine fault codes can be cleared, always only after you confirm. Note: clearing also resets the readiness monitors, which matters for an emissions test.

Does Car-Z work with an electric smart?

Partly. Electric cars don't have to support standard OBD, so usually only the 12-volt voltage and a few values come through. Battery health is manufacturer data and isn't shown.

Which plug do I need?

An ordinary, open OBD2 plug with Bluetooth LE that understands the standard ELM327 commands. Not a closed plug that only works with its maker's own app. The guides list which plugs we've tested and how to connect them.

Can Car-Z code or program my smart?

No. Car-Z reads standard OBD: live data and engine fault codes. Coding, programming and service resets need manufacturer-specific tools.

Sources

  1. Directive 98/69/EC (EUR-Lex)
  2. OVMS – OBD-II vehicles (EV notes)
  3. Klavkarr – OBD port location Smart

How sure we are: Medium: based on reliable sources, with some details per model still uncertain.

← All makes

Ready to read your smart?

Put a in the port, open the app and connect.